i used some spray to glue the paper to the plexi, and then to the inside of the bag (pic 10)ħ) on the sides of the purse are two circles. Then i took a heating gun to the plexiglass and bent it a tad to match the curve of the purse.Ħ)I found a print of the buttons online.(pic 9) I used photoshop to get it to the right size. Take your plexiglass and cut out the shape of your heart. (pic 7)Ĥ) use the same paper heart template to create a yellow border out of craft foam. Once done, use an exacto knife and cut it out. Use the template and draw it onto the front of the bag. (pic 4,5, 6)ģ) draw out a heart on a piece of scratch paper for the front.
![big hero 6 honey lemon big hero 6 honey lemon](https://i.ytimg.com/vi/-ROWISBd5c8/maxresdefault.jpg)
This way, the bag can open and close, but you don't see the seam in pictures. HOWEVER, i did not glue it to the back of the bag. i glued it right onto the front of the bag. (pic 1,2, 3)Ģ) now, take a pieces of craft foam that is the width of the bag. So, cut 2 side pieces, a bottom, and a front and back. I wanted to make it functional, so i knew it was going to be hollow. You should now be at this point in assemblyġ) Start off by making the general shape of the purse from EVA foam. I had some mesh laying around so i wrapped it around her legs and then sprayed. I asked her to wear them as i took my air brush and sprayed on a criss/cross pattern on it. I used the legs of stockings as arms and the waistband as the turtle neck part.Ħ) for thumbs, i just cut a little hole where the thumbs poke out in the sleeves.ġ) We found some purple-ish tights at target. Then cut off the waist band and then then right in half at the crotch. Cut up your strips and sew them onto the dress (pic 3 and 4)ĥ) in order to get the new sleeves, i grabbed pair of purple stockings from target. I then used the original pink fabric from the sleeves of the jacket in order to make the accents. (pic 1)ģ) it was just a bit too bright pink for me, so i took it to the basement and sprayed it down with some purple to mute the color a bit. I removed all the extra stuff, like the buckles, buttons, and sleeves.Ģ) Then, I sewed the jacket closed so that it was now a dress. cut out those sections(pic 10, 11)ġ) we got lucky and found a pink rain jacket at a thrift store. You can use either craft foam or EVA foam, depending how thick you want it to be. Basically anything that you want elevated. Glue in place once completed.ġ0) From there, grab your paper templates and draw in your extra details, such as extra plating, pectoral pieces, etc. I just took some extra foam, placed it in the vacant gap where the shoulder strap would be, mark it, and then cut it. (pic 10)ġ0) now get more foam and put it into the shoulder sections. Cut it out with a template and glue in a solid piece. i needed to replace that circle with one solid piece of foam. Since i glued her chest armor together from three pieces, the pieces all conjoin right in the center. Now glue them together.(pic 9 )ĩ) Honey lemon has a circle in the center of her armor, where the bottom of her sternum is. (pic 8)Ĩ) Just as you overlapped the side pieces, overlap the two back pieces till they are nice and contoured to the shape of your body. It will look nicer if the armor is more contoured to your body. The reason for this is that your back is not perfectly flat. From there, cut the back piece in half where the crease is.
![big hero 6 honey lemon big hero 6 honey lemon](https://www.coloringpages101.com/coloring-pages/Cartoon-Movies/Big-Hero-6/Hiro-and-Baymax-coloring-page.png)
Glue your plastic buckles onto both sides and clip them in. Mark off the excess foam and cut them off. Overlap the side flaps of the chest over the side flaps of the back piece. The reason you added an extra inch to the width is so that you can make the fitting flush. (pic 5) once you have all the left and right breast plates, and you have the abdomen cover, glue all three pieces together.Ħ) From there, press the chest AND back foam pieces onto the person. Push and pull the EVA foam on the bowl to get the foam to the curve you want it. From there, grab a bowl and use it as a round object to place the warm EVA on. left, right, and abdomen.ĥ) In order to make the curves for the breast plate, heat the foam with a heating gun. From there, i started cutting out the segments of Honey Lemon's armor. (pic 3)Ĥ) Cut these out from the EVA foam (pic 4). When you unfold it, you should have the front piece (pic 2) *this pics is not the actual chest plate, but the concept is the same.ģ) do the same process for the back. From there, cut out that measured rectangle out of the scratch paper.Ģ) fold it in half, draw in your template and then start cutting out the general shape from the folded paper (pic 1). 1)For the chest, take your tape measure and measure from the shoulder to the bottom of your rib cage.